Categories: Utopia

Utopia Elite Edition VR Headset User Manual

GETTING STARTED

Device Features

See quick start guide for list of recommended apps.
Once downloaded, open the app. Some apps will not default into
split screen VR mode. You may need to go to the app settings to
turn this on. It should look like the image below:

Open the cover to the VR headset and place your device onto the ledge above the hinges. It is recommended to remove the phone case for best fit.
If using with headphones or a charge cable (not included), plug these in before closing the cover.
Put on the headset and adjust the straps for comfort

Caution: If wearing glasses, be careful when putting on headset. Some glasses may not fit or be uncomfortable. If this occurs, it is recommended to use contacts.

Use the wheel on the top of the headset to adjust the interpupillary distance. Adjust the lenses to fit the distance between the eyes for maximum field of view.
Use the focal adjustment wheels to adjust the focus for each individual eye.
Take a 10-15 minute break every 30 minutes.

HEADPHONES

Pull out the 3.5 mm audio cable and insert the connector into the phone’s headphone jack. Close the cover. iPhone 7 users will need the adapter supplied with the phone.

The volume control switch is located on the bottom of the headset. Flick in either direction to raise/lower the volume. Press in to play/pause. On some phones, holding play will activate Siri or Google Voice Assistant.

HEALTH & SAFETY

General Precautions:

Headset should only be used by children while under adult super vision.
Take at least a 10 to 15 minute break every 30 minutes, even if you don’t think you need it. Each person is different, so take more frequent and longer breaks if you feel discomfort. You should decide what works best for you.
Consult your doctor before using the headset if you are pregnant, elderly, have pre-existing binocular vision abnormalities or psychiatric disorders, or suffer from a heart condition or other serious medical condition.
A comfortable virtual reality experience requires an unimpaired sense of motion and balance. Do not use the headset when you are: Tired; need sleep; under the influence of alcohol or drugs; hung-over; have digestive problems; under emotional stress or anxiety; or when suffering from cold, flu, headaches, migraines, or earaches, as this can increase your susceptibility to adverse symptoms.
Use only in a safe environment. The headset produces an immersive virtual reality experience that distracts you from and completely blocks your view of your actual surroundings. Always be aware of your surroundings before use and while using the headset. Use caution to avoid injury.
Use of the headset may cause loss of balance.
Never wear the headset in situations that require attention, such as walking, bicycling, or driving.
Do not use the headset while in a moving vehicle such as a car, bus, or train, as this can increase your susceptibility to adverse symptoms.

Seizures:

If you have ever had, or currently live with, symptoms of epilepsy such as severe dizziness, blackouts, seizures or loss of awareness, you should see a doctor before using this product. The content viewed through the headset may include flashing images and repetitive sequences, which could cause seizures, even in those who have never experienced seizures in the past.

Immediately stop playing and consult a doctor if you experience any of these symptoms. Parents should watch for or ask their children about the above symptoms. Children and teenagers are more likely than adults to experience these seizures.

Customer Service:
877-499-6072
support@myretrak.com
955 Freeport Pkwy, Suite 100, Coppell, TX 75019
(Please be prepared to provide proof of purchase.)

1. PARTS

Charge Indicator: Red light indicates the internal camera battery is charging. It will stay solid if the camera is charging either from a micro USB power source or the external battery is charging the internal battery

WiFi/Record Indicator: Blue light indicates the WiFi status. Blinking means it is booting up. Solid means the camera is outputting a steady WiFi signal. Blinks when capturing a photo/video (transmitting data). In independent mode (if using the camera with no SD card and no connection to your mobile device) when recording video the blue light will flash constantly.

Power Indicator: Green light indicates powered on/off status Green light indicates the power status of both batteries:

If the LED indicator flashes once, the battery is zero to 25%.
If the LED flashes twice, the battery is between 25%-50%.
If the LED flashes three times, the battery is 50%-75%.
If the LED flash four times, its battery is between 75%-100%.
If the LED is constant the battery is fully charged and powered on.

Charging Time:

Internal battery – 800mAh capacity @ 1 amp input approximately 1-2 hours depending on the charger output.

Removable battery – 500mAh capacity @ 1amp input approximately 45 minutes – 1.5 hours depending on the charger output.

Shutter Button Functions: Hold down the shutter button for 2 seconds to turn on the for between .4s and 1.8s to record video. When recording video, the blue light will flash continuously. Hold down the shutter button for 3.5 seconds to turn off the camera.

Power Bank LED Indicator: If the LED indicator flashes once, the battery is zero to 25%. If the LED flashes twice, the battery is between 25%-50%. If the LED flashes three times, the battery is 50%-75%. If the LED flash four times, its battery is between 75%-100%. If the LED is constant, the battery is fully charged.

2. Getting Started

Charging the Battery
Using the supplied Micro USB cable, plug the camera into a 5V USB charger. A red LED light will turn on when the camera is charging. Once fully charged, the red light will turn off. A green light will flash when the battery is low.
The device is limited to use with a USB power adapter with an output power rating of 5V/1.5A. Charging with other adapters may damage the battery.

Power On & Power Off
Power On: Push down the shutter button for 2 seconds and then release it. After a short time, a blue light will come on indicating that the camera’s WiFi network is accessible and you are ready to connect. It may take up to 10 seconds for the blue light to come on.
Power Off: Push down the shutter button for 3.5 seconds and then release it. A blue light will flash, and once all the lights go out, the device has successfully powered off.

INSERT AND REMOVE THE MICRO SD CARD

The camera supports a Micro SD card with a maximum capacity of 128GB. However, a card over 32GB cannot be used in the FAT file format. To use an SD card over 32GB you must reformat to NTFS formatting. To prevent damage or file loss, it is recommended to power off the camera before inserting and removing the Micro SD card.

☆ A class 10 SD card is recommended for high speed video reading/writing.
☆ Reformatting an SD card: connect the SD card through a card reader to your computer. Find your SD card as a drive in ‘My Computer’ then right click, select formatting and choose NTFS to start formatting. This will erase all content on the SD card.

Use Mode

Independent Operation
To use the camera without connecting to WiFi, power on the camera and push the shutter button to take a picture. Hold the shutter button down between .4s to 1.8s to record a video. When recording video, the blue light will flash continuously.

APP
USB Connection
Download the ‘Utopia 360’ app to your device through the Apple App Store or the Google Play Store. Connect the camera directly to your Micro USB or USB-C enabled device by using the double-sided USB adapter. The side with the arrow should be inserted into the camera, and will only fit when inserted in the right direction. The below message will then be displayed:

Once you tap “OK”, the ‘Utopia 360’ app will open. If you select “Use by default for this USB device”, the app will automatically launch every time the camera is connected. After connecting, the ‘Utopia 360’ interface will appear as shown in figure 4:

3. Connecting Through WiFi

Download the ‘Utopia 360’ app to your device through the Apple App Store or the Google Play Store. When you open the app, you will see the ‘Utopia 360’ app interface as shown in Figure 5.

You will be prompted to connect to your camera’s WiFi network. Go to your WiFi settings and connect to the ‘Utopia 360 ####’ network using the default password ‘12345678’. The default password can later be changed in the camera’s settings menu.

Once you are connected to WiFi, return to the ‘Utopia 360’ app to see the preview interface as shown in figure 7.

4. Software Use

Mobile APP

Android: Click on the link above to download the APK for the camera. You can also download it from the Google Play Store. The application supports Android 5.0 and above, and the device must support OTG for use with a USB connection. Some devices may require you to enable or allow the OTG connection. The WiFi connection will work with all WiFi enabled devices.

iOS: Click on the link above to download the ‘Utopia 360’ app for the camera. You can also download it from the iTunes App store.

Buttons introduction
Double tap your screen in preview mode to change between shooting modes: Panorama, Fisheye, and Asteroid

Share
Your mobile device must be connected to a WiFi network before you can share content or live stream.
Share: Tap the “Select” button on the top right corner of the Local Gallery/Cloud Gallery to select the content you want to share. After selecting content, tap the Share icon in the lower left corner of the interface to share. See Figure 8 for sharing options.

You can share photos or videos directly to Facebook. You can also upload videos directly to YouTube. If you select the photo or video and save to your Local Gallery, the photos/videos can be saved to your device. You can then share these photos to other pre-installed social media apps like Instagram by selecting “Others”.

YouTube

Live Streaming

The camera can live stream through YouTube and Facebook. Tap the “Live” button to select the live platform, as shown in Figure 10.

You will enter the YouTube Live interface after you select the YouTube platform, as shown in figure 11:

Tap “Not login” to log in with a Google account. You can also log into a Google account in the “Me” section. Figure 12 shows the interface after you’ve logged in.

If you’re signed into an account that does not have Live permissions on YouTube, you must turn on Live permissions through the web login URL (http://www.youtube.com/features): Set live streaming permissions on the site, as shown in Figure 13:

Select Enable in Live Streaming to turn on live permissions.

You can input the live stream title, choose a resolution, and set Privacy. Select Start Live Stream to start, as shown in figure 14:

The live interface as shown in figure 15:

You can share the live stream with your friends through a URL. If you want to stop live streaming, just tap the Stop Live button. The live interface of YouTube is shown in figure 16:

Facebook

You will enter the Facebook Live interface when you select the Facebook Live platform, as shown in Figure 17:

Input a title for your live stream, select the resolution, and adjust privacy settings. Once you tap “Start Live Stream”, the app will prompt you to log into Facebook and give app permission. If you are already logged in, the live stream will begin.

If you want to stop live streaming, just tap “Stop Live” as shown in figure 20.

You can view the live stream on the Facebook site or Facebook app during or after the stream.

Camera Settings

Select Camera Settings to enter the below menu, as shown in figure 21:

Video resolution: you can set the camera’s resolution to 2048×1024 or 1920×960.
Device: You can view the Camera’s Module type, Serial number, and Firmware version.